banner_page

LM358DRG3

2 Channels 30mA per Channel 20nA 65 dB Instrumentational OP Amps 0.5μA 16V 3V~32V ±1.5V~16V LM358 8 Pins 8-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-LM358DRG3
  • Package: 8-SOIC (0.154, 3.90mm Width)
  • Datasheet: -
  • Stock: 164
  • Description: 2 Channels 30mA per Channel 20nA 65 dB Instrumentational OP Amps 0.5μA 16V 3V~32V ±1.5V~16V LM358 8 Pins 8-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 3 days ago)
Contact Plating Tin
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-SOIC (0.154, 3.90mm Width)
Number of Pins 8
Operating Temperature 0°C~70°C
Packaging Tape & Reel (TR)
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Subcategory Operational Amplifier
Packing Method TR
Technology BIPOLAR
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 5V
Base Part Number LM358
Pin Count 8
Operating Supply Voltage 16V
Number of Channels 2
Operating Supply Current 1mA
Nominal Supply Current 1mA
Output Current 20mA
Slew Rate 0.3V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 65 dB
Current - Input Bias 20nA
Voltage - Supply, Single/Dual (±) 3V~32V ±1.5V~16V
Output Current per Channel 30mA
Input Offset Voltage (Vos) 3mV
Bandwidth 700 kHz
Unity Gain BW-Nom 700 kHz
Voltage Gain 100dB
Average Bias Current-Max (IIB) 0.5μA
Power Supply Rejection Ratio (PSRR) 65dB
Low-Offset NO
Frequency Compensation YES
Low-Bias NO
Micropower NO
Programmable Power NO
Input Offset Current-Max (IIO) 0.05μA
Height 1.75mm
Length 4.9mm
Width 3.91mm
Thickness 1.58mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

LM358DRG3 Overview


Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. Buffer amplifier has a total of 8 pins. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 8 pins are located on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. For this electronic part, it is recommended that you mount it with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. A supply current of 1mA can be used to operate this linear amplifier. Keeping the voltage gain at 100dB is the best course of action. Op amp ic has 2 channels. The operating supply voltage of the buffer op amp is rated at 16V. For packing the buffer amplifier, the TR-axis is adopted.

LM358DRG3 Features


8 Pins
supply voltage of 5V
100dB voltage gain

LM358DRG3 Applications


There are a lot of Texas Instruments LM358DRG3 Instrumentational OP Amps applications.

  • Comparator
  • Exponential operation circuits
  • Blood pressure sensors
  • Vehicle electronics
  • Portable media players
  • Strain gauges
  • E-book readers
  • Power transmission
  • Weak signal detection
  • Semiconductor detectors

Write a review

Note: HTML is not translated!
    Bad           Good