LM5025AMTC
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Frequency | 1MHz |
| Base Part Number | LM5025 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 48V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive, Isolation Capable |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | 8V~15V |
| Output Power | 300W |
| Control Features | Dead Time Control, Frequency Control, Ramp, Soft Start |
| Topology | Forward Converter |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 200kHz~580kHz |
| Input Voltage (Max) | 90V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 20ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 15 ns |
| Switcher Configuration | PUSH-PULL |
| Max Duty Cycle | 80 % |
| Clock Sync | Yes |
| Output Phases | 1 |
| Length | 5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
LM5025AMTC Overview
The switching controller fits in the 16-TSSOP (0.173, 4.40mm Width) package and is ideal for most applications. For 2 outputs, the dc motor controller is appropriate. There is a Tube solid enclosure around the pmic. Transistor Driver dc switching's outputs (s) are supported. This dc control operates at 8V~15V and has a 8V~15V supply voltage. Suitable for a -40°C~125°C TJ dc switcher. The switching controller is capable of switching at the 200kHz~580kHz position. As it has a Surface Mount value, it can be used for general dc dc regulator. For efficient switching control, the dcdc regulator features Dead Time Control, Frequency Control, Ramp, Soft Start. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. There are a terminal (s) on the switching converters that are designed at DUAL. A variety of terminations with 16 of dc switching. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. DC switcher's input voltageis 48V volts. Other relevant dc to dc converter ics will be returned if you search "LM5025". In total, switching converter has 16 pins. Switching converter is a type of Switching Regulator or Controllers in particular. At most, the dc to dc regulator accepts 90V input voltage. You should note that the dc dc regulator's usual output current is 1A. As a result of this, the maximum duty cycle of the voltage regulator dc to dc must remain 80 % during power-up and power-down. DC switcher's Surface Mount qualifies it for most applications and prototypes. Switching controller operates at 1MHz Hz.
LM5025AMTC Features
Transistor Driver Outputs
Switching Frequency: 200kHz~580kHz
Dead Time Control, Frequency Control, Ramp, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 80 %
Frequency: 1MHz
LM5025AMTC Applications
There are a lot of Texas Instruments LM5025AMTC DC to DC converter applications.
- Experimental setup
- Power supplies of electronic gadgets
- PSRR circuits
- Game consoles
- Alternators
- Flaw detection equipment
- Motor controller circuits
- Hydro power
- Elevator lighting
- Servo drive system
