LM5033MM/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Frequency | 1MHz |
| Base Part Number | LM5033 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 250mV |
| Output Type | PWM Signal |
| Input Voltage-Nom | 48V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Operating Supply Current | 2mA |
| Output Configuration | Positive |
| Output Current | 100mA |
| Voltage - Supply (Vcc/Vdd) | 15V~90V |
| Quiescent Current | 150μA |
| Output Power | 500W |
| Control Features | Frequency Control, Soft Start |
| Topology | Full-Bridge, Half-Bridge, Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 200kHz 600kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 16ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 16 ns |
| Nominal Input Voltage | 90V |
| Isolation | Non-Isolated |
| Output Phases | 1 |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 1.02mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM5033MM/NOPB Overview
With a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) package, the switching controller is suitable for a wide range of applications. The dc motor controller is adquate to generate for 2 outputs. A solid enclosure of Tape & Reel (TR) surrounds pmic. PWM Signal dc switching's outputs (s) can be handled by it. Voltages 15V~90V are the dc control's supply voltage and operating voltage, respectively. Worked in a -40°C~125°C TJ dc switcher before. It can switch at 200kHz 600kHz. dc dc regulator is made easier with Surface Mount. Featured in the dcdc regulator is Frequency Control, Soft Start which allows efficient switching control. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. A switching converters's terminal (s) sits at the DUAL position. Different dc switching's functions can be applied to 10 terminations. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. It is inputted with a DC switcher's voltage of 48V. A search for "LM5033" will reveal other relevant dc to dc converter ics. Switching converter has a total of 10 pins. Specifically, switching converter falls under the Switching Regulator or Controllers category. As determined by the test statistics, the output voltage of DC regulator is 250mV. In most cases, the dc dc regulator's output current is 100mA. This information should be noted when you begin working with the component. DC switcher's Surface Mount makes it qualified for most application and prototype designs. DC switcher'sA frequency of 1MHz is used by the switching controller. During dormancy, the dc switching uses 150μA. Input voltage can be set to 90V for nominal working status. 2mA volts is the supply current.
LM5033MM/NOPB Features
PWM Signal Outputs
Switching Frequency: 200kHz 600kHz
Frequency Control, Soft Start
PULSE WIDTH MODULATION
Frequency: 1MHz
LM5033MM/NOPB Applications
There are a lot of Texas Instruments LM5033MM/NOPB DC to DC converter applications.
- Servo drive system
- Computer monitoring equipment of building
- Constant current circuits
- Serial communication converter
- ATMs
- Surface processing equipment
- Emergency lighting monitoring equipment
- Linear guide
- Photovoltaic power
- Ball screw pair
