LM5085MM/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Base Part Number | LM5085 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 75V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 48V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Operating Supply Current | 1.3mA |
| Output Configuration | Positive |
| Output Current | 1.75A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~75V |
| Quiescent Current | 1.3mA |
| Control Features | Current Limit, Enable, On Time Control |
| Input Voltage (Min) | 4.5V |
| Topology | Buck |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | Up to 1MHz |
| Synchronous Rectifier | No |
| Max Frequency | 1MHz |
| Max Duty Cycle | 100 % |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM5085MM/NOPB Overview
With a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) package, the switching controller is suitable for a wide range of applications. For outputs of 1, this dc motor controller is suitable. PMIC is packaged in a solid enclosure of Tape & Reel (TR). The program can handle Transistor Driver dc switching's outputs (s). The supply and operating voltage of the dc control are 4.5V~75V. A -40°C~125°C TJ dc switcher is not a problem. The switching controller can be switched at Up to 1MHz. As it has a Surface Mount value, it can be used for general dc dc regulator. To provide efficient switching control, Current Limit, Enable, On Time Control is included in the dcdc regulator. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. DUAL are the position of the terminal of the switching converters. A variety of 8 terminations are available in dc switching. The DC switcher's nominal voltage is 48V. LM5085 can be searched for other relevant dc to dc converter ics. There are 8 pins on switching converter. Switching converter is a special type of Switching Regulator or Controllers. It is recommended that the input voltage of the dc dc voltage regulator be 4.5V. DC regulator outputs 75V voltage according to the test statistics. If you start a project, note down the dc dc regulator's usual output current of 1.75A. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 100 %. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. There is a maximum frequency of 1MHz on this dc regulators. DC switching uses 1.3mA when it is dormant. There is a 1.3mA volt supply current.
LM5085MM/NOPB Features
Transistor Driver Outputs
Switching Frequency: Up to 1MHz
Current Limit, Enable, On Time Control
Max Duty Cycle: 100 %
LM5085MM/NOPB Applications
There are a lot of Texas Instruments LM5085MM/NOPB DC to DC converter applications.
- Radio equipment
- Hydrogen power
- Electric water heaters
- Low output voltage switching power supply circuits
- Hydro power
- Energy management systems
- Thermal power
- Analog precision reference circuits
- Experimental setup
- Communication system
