LM5088MH-2/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-PowerTSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 1MHz |
| Base Part Number | LM5088 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 1.205V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 48V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 10A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~75V |
| Quiescent Current | 3.8mA |
| Control Features | Enable, Frequency Control, Ramp, Soft Start |
| Topology | Buck |
| Min Input Voltage | 4.5V |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 50kHz~1MHz |
| Max Input Voltage | 75V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Min Output Voltage | 1.205V |
| Switcher Configuration | SINGLE |
| Max Duty Cycle | 94 % |
| Clock Sync | Yes |
| Duty Cycle | 97 % |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM5088MH-2/NOPB Overview
In the 16-PowerTSSOP (0.173, 4.40mm Width) package, the switching controller meets most application requirements. It is sufficient to generate 1 outputs with this dc motor controller. An enclosure of Tube is used to package the PMIC. Transistor Driver dc switching's outputs (s) are supported. 4.5V~75V is the operating voltage and supply voltage of the dc control. Work well in dc switchers with a -40°C~125°C TJ. A switching controller such as this can switch at a value of 50kHz~1MHz . The Surface Mount allows it to be used for dc dc regulator in general. For efficient switching control, the dcdc regulator features Enable, Frequency Control, Ramp, Soft Start. A SWITCHING CONTROLLER analog IC is connected to the switch converters. switching converters terminal (s) are designed to be at DUAL. A variety of 16 terminations are available in dc switching. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. DC switcher's voltage input is 48V. Other relevant dc to dc converter ics will be returned if you search "LM5088". The switching converter has a total of 16 pins. DC regulator outputs 1.205V voltage based on test statistics. You should note down the dc dc regulator's usual output current of 10A when you start a project. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 94 %. In most applications and prototypes, DC switcher's Surface Mount makes it suitable. Switching controllers operate at 1MHz frequencies. DC switching uses 3.8mA when it is dormant. The maximum input voltage of this dc switcher is 75V, so users must limit the voltage accordingly. 4.5V is the required supply voltage. A voltage controller's lowest output voltage cannot be less than 1.205V.
LM5088MH-2/NOPB Features
Transistor Driver Outputs
Switching Frequency: 50kHz~1MHz
Enable, Frequency Control, Ramp, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 94 %
Frequency: 1MHz
LM5088MH-2/NOPB Applications
There are a lot of Texas Instruments LM5088MH-2/NOPB DC to DC converter applications.
- Flexible manufacturing cells
- Current source circuits
- Hydrogen power
- Precision electronic equipment
- Analog precision reference circuits
- Boring machines
- Electrical distribution systems
- Motor controller circuits
- Imported equipment
- Wind power
