LM5116MH/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-PowerTSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Base Part Number | LM5116 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 80V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 48V |
| Voltage | 100V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20A |
| Voltage - Supply (Vcc/Vdd) | 6V~100V |
| Quiescent Current | 4.6mA |
| Control Features | Enable, Frequency Control, Ramp, Soft Start |
| Max Output Voltage | 80V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 200kHz 535kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Nominal Input Voltage | 100V |
| Min Output Voltage | 1.215V |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 1MHz |
| Max Duty Cycle | 98 % |
| Duty Cycle | 98 % |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM5116MH/NOPB Overview
It comes in a 20-PowerTSSOP (0.173, 4.40mm Width) package, so switching controller can be used for most applications. This dc motor controller can be used to generate outputs with 1 numbers. There is a Tube solid enclosure around the pmic. There are Transistor Driver dc switching's output (s) that it can handle. dc control's supply and operating voltages are 6V~100V. Workable in an dc switcher where -40°C~125°C TJ is the -40°C~125°C TJrm. With this switching controller, you can switch at 200kHz 535kHz. dc dc regulator is made easier with Surface Mount. Switching control is made easier with the dcdc regulator's Enable, Frequency Control, Ramp, Soft Start. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. The switching converters's terminals (s) are designed at DUAL. A variety of dc switching's functions can be performed on 20 terminations. It includes PULSE WIDTH MODULATION as one of the control techniques dc dc converter ic adapts. DC switcher's voltage input is 48V. You can find other relevant dc to dc converter ics by searching "LM5116". Pins number 20 of switching converter in total. Statistically, the DC regulator outputs 80V voltage. You should note that the dc dc regulator's usual output current is 20A. voltage regulator dc to dcs with a 98 % duty cycle are designed to be reliable when powered on and powered off. This Surface Mount makes DC switcher suitable for most prototypes and applications. DC regulator1MHz has the maximum frequency. DC switchings that are dormant use 4.6mA. For nominal working status, the input voltage can be set as 100V. Datasheets state the switching converter can output up to 80V volts. At least 1.215V voltage is output by the voltage controller.
LM5116MH/NOPB Features
Transistor Driver Outputs
Switching Frequency: 200kHz 535kHz
Enable, Frequency Control, Ramp, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 98 %
LM5116MH/NOPB Applications
There are a lot of Texas Instruments LM5116MH/NOPB DC to DC converter applications.
- Gear/thread machining machines
- Post equipment
- Bending machines
- Grinders
- Surge protection circuits
- Emergency lighting monitoring equipment
- Boring machines
- Remotely powered electric motors
- Drilling machines
- Scientific research
