LM7372MR
| Parameters | |
|---|---|
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | LM7372 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 2 |
| Operating Supply Current | 13mA |
| Nominal Supply Current | 13mA |
| Output Current | 150mA |
| Max Supply Current | 16mA |
| Slew Rate | 3000V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 2.7μA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 260mA |
| Input Offset Voltage (Vos) | 8mV |
| Bandwidth | 120MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 100000 kHz |
| Voltage Gain | 78dB |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 220MHz |
| Bias Current-Max (IIB) @25C | 10μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Height | 1.47mm |
| Length | 4.93mm |
| Width | 3.94mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-PowerSOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | VIP™ III |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Packing Method | RAIL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
LM7372MR Overview
Op amp is packaged in 8-PowerSOIC (0.154, 3.90mm Width) case. The instrumentation amplifier in this picture is of the Voltage Feedback-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. The number of terminations approaches 8. The total number of pins on linear amplifier is 8. It is important to remember that this op amp should be operated at a voltage of 5V volts. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 8 pins are located on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 8mV. The mounting type that is recommended for this electrical part is Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureYou can run this op amp ic on 13mA . Keeping the voltage gain at 78dB is the best course of action. There are a total of 2 channels available on the op amps. The operating supply voltage of the buffer op amp is rated at 18V. The instrumentation amplifier is packed in the form of RAIL. VIP? III corresponds to linear amplifier's series.
LM7372MR Features
8 Pins
supply voltage of 5V
78dB voltage gain
LM7372MR Applications
There are a lot of Texas Instruments LM7372MR Instrumentational OP Amps applications.
- Band-stop filter
- Tablets
- Fission chambers
- Weak signal detection
- Weighing systems
- Radiation thermometry transducers
- Displayers for aircraft and air transportation control systems
- Radar
- Scintillation detectors
- Car stereo
