LM7372MR/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-PowerSOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | VIP™ III |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | LM7372 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-5/+-15V |
| Number of Channels | 2 |
| Operating Supply Current | 13mA |
| Nominal Supply Current | 13mA |
| Output Current | 150mA |
| Slew Rate | 3000V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 2.7μA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 260mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 120MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 120000 kHz |
| Voltage Gain | 78dB |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 220MHz |
| Bias Current-Max (IIB) @25C | 10μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Input Offset Current-Max (IIO) | 4μA |
| Height | 1.7mm |
| Length | 4.89mm |
| Width | 3.9mm |
| Thickness | 1.48mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM7372MR/NOPB Overview
A 8-PowerSOIC (0.154, 3.90mm Width) case is used to package the op amp. The instrumentation amplifier in this picture is of the Voltage Feedback-type. Upon delivery, op amp ic is packaged in a Tube case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are located on this board. This linear amplifier should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are included on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 2mV. This electrical part should be mounted using type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. Using a supply current of 13mA , this buffer op amp will be able to operate. It is recommended to keep the voltage gain at 78dB at all times. As far as the device is concerned, buffer amplifier has 2 channels. The operating supply voltage of instrumentation amplifier is rated 18V voltage. Buffer op amp series numbers are indicated by the VIP? III.
LM7372MR/NOPB Features
8 Pins
supply voltage of 5V
78dB voltage gain
LM7372MR/NOPB Applications
There are a lot of Texas Instruments LM7372MR/NOPB Instrumentational OP Amps applications.
- Switching amplifier
- Mobile phone
- earphone
- Inverse/same-phase proportional circuit
- PDA
- Industrial control system
- Blood pressure sensors
- Power control
- Hand-held batteries
- Portable electronic products powered by batteries
