LM833MM/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 500mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | LM833 |
| Pin Count | 8 |
| Number of Elements | 2 |
| Operating Supply Current | 5mA |
| Nominal Supply Current | 5mA |
| Power Dissipation | 500mW |
| Output Current | 40mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Audio |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 500nA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 5mV |
| Gain Bandwidth Product | 15MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 15000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 1μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 300μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 1μA |
| Programmable Power | NO |
| Wideband | NO |
| Load Impedance | 2kOhm |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM833MM/NOPB Overview
There is a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case in which the instrumentation amplifier is packaged. The instrumentation amplifier in this picture is of the Audio-type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. The number of terminations approaches 8. The total number of pins on linear amplifier is 8. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. There are 8 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 5mV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. You can run this op amp ic on 5mA . 110dB should be the voltage gain. For the operating supply voltage of the op amp ic, there is a rating of 2. It is used TR to pack the op amps.
LM833MM/NOPB Features
8 Pins
supply voltage of 15V
110dB voltage gain
LM833MM/NOPB Applications
There are a lot of Texas Instruments LM833MM/NOPB Instrumentational OP Amps applications.
- E-book readers
- Weighing systems
- Logarithmic operation circuits
- Industrial applications including automation
- Semiconductor detectors
- Proportional counter tubes
- High/low-pass filter circuit
- Micro signal measurement
- Non-polarized electrodes
- Integrator circuits
