LMC6464AIM/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 11 hours ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | LMC6464 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/15V |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Nominal Supply Current | 90μA |
| Output Current | 75mA |
| Slew Rate | 0.028V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 0.15pA |
| Voltage - Supply, Single/Dual (±) | 3V~15.5V ±1.5V~7.75V |
| Output Current per Channel | 75mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 50 kHz |
| Unity Gain BW-Nom | 50 kHz |
| Voltage Gain | 129.54dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 16V |
| Voltage - Input Offset | 250μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Input Offset Current-Max (IIO) | 0.000005μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMC6464AIM/NOPB Overview
A 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. This is a General Purpose type op amp. Instrumentation amplifier is delivered in a Tube case. It is estimated that there will be 14 terminations in the next few months. In this case, there are 14 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. The buffer op amp includes 14 pins. The input offset voltage is 500μV. This electrical part should be mounted using type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureKeeping the voltage gain at 129.54dB is the best course of action. The buffer amp consists of 4 circuits in total. Buffer op amp is equipped with 4 channels on the device. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals.
LMC6464AIM/NOPB Features
14 Pins
supply voltage of 5V
129.54dB voltage gain
Output Type: Rail-to-Rail
LMC6464AIM/NOPB Applications
There are a lot of Texas Instruments LMC6464AIM/NOPB Instrumentational OP Amps applications.
- Video data acquisition
- Signal amplification
- Proportional counter tubes
- Navigation
- PDA
- Micro signal measurement
- Industrial control system
- MP3
- Video amplifiers
- Laptop
