LMC6464BIMX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LMC6464 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 3/15V |
| Operating Supply Current | 90μA |
| Nominal Supply Current | 90μA |
| Output Current | 75mA |
| Slew Rate | 0.028V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 0.15pA |
| Voltage - Supply, Single/Dual (±) | 3V~15.5V ±1.5V~7.75V |
| Output Current per Channel | 75mA |
| Input Offset Voltage (Vos) | 250μV |
| Gain Bandwidth Product | 50kHz |
| Unity Gain BW-Nom | 50 kHz |
| Voltage Gain | 129.54dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 65dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 16V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
LMC6464BIMX Overview
There is a 14-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. This is a General Purpose type op amp. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. The number of terminations approaches 14. In this case, there are 14 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. It should be noted that this op amp is a type of Operational Amplifier device. In total, the buffer amplifier consists of 14 pins. In terms of input offset voltage, operational amplifier rates 250μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Using a supply current of 90μA , this buffer op amp will be able to operate. There should be no change in the voltage gain at 129.54dB. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. There are 4 elements in total in this linear amplifier. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted.
LMC6464BIMX Features
14 Pins
supply voltage of 5V
129.54dB voltage gain
Output Type: Rail-to-Rail
LMC6464BIMX Applications
There are a lot of Texas Instruments LMC6464BIMX Instrumentational OP Amps applications.
- Weak signal detection
- Vehicle electronics
- pH (acidity)
- Scintillation detectors
- Commercial audio systems
- RF cable systems
- earphone
- Video conversion and routing
- Strain gauges
- Multiplication circuits
