LMC660AIM/NOPB
| Parameters | |
|---|---|
| Number of Channels | 4 |
| Voltage | 32V |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 1.5mA |
| Output Current | 40mA |
| Slew Rate | 1.1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 0.002pA |
| Voltage - Supply, Single/Dual (±) | 4.75V~15.5V ±2.38V~7.75V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 1.4MHz |
| Unity Gain BW-Nom | 1400 kHz |
| Voltage Gain | 126.02dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Input Offset Current-Max (IIO) | 0.000002μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | LMC660 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 5/15V |
LMC660AIM/NOPB Overview
It is packaged in an 14-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. An op amp of this type is a General Purpose-type. In the case of Tube cases, linear amplifier will be delivered. We are approaching the 14h termination of the year. The total number of pins on linear amplifier is 14. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. A total of 14 pins are present on the instrumentation amplifier. Op amp ic rates 1mV for input offset voltage. Surface Mount is the recommended mounting type for this linear amplifier. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. It is possible to operate this buffer amplifier from a supply current of 1.5mA . Voltage gain should remain at 126.02dB. There are 4 channels on the operational amplifiers. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals.
LMC660AIM/NOPB Features
14 Pins
supply voltage of 5V
126.02dB voltage gain
Output Type: Rail-to-Rail
LMC660AIM/NOPB Applications
There are a lot of Texas Instruments LMC660AIM/NOPB Instrumentational OP Amps applications.
- Switching amplifier
- Vehicle electronics
- RF cable systems
- Radar
- MP3
- Weighing systems
- Blood pressure sensors
- Industrial control system
- Inverse/same-phase proportional circuit
- Precision measurement
