LMC662AIM/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | LMC662 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 5/15V |
| Number of Channels | 2 |
| Operating Supply Current | 750μA |
| Nominal Supply Current | 750μA |
| Output Current | 40mA |
| Slew Rate | 1.1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 0.002pA |
| Voltage - Supply, Single/Dual (±) | 4.75V~15.5V ±2.38V~7.75V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 1.4MHz |
| Unity Gain BW-Nom | 1400 kHz |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.000004μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 16V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000004μA |
| Programmable Power | NO |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMC662AIM/NOPB Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. The instrumentation amplifier in this picture is of the General Purpose-type. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. It is estimated that there will be at least 8 terminations this year. The pins on this board total to 8 in total. Please take in mind that this instrumentation amplifier should be run at 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. The op amp ic has an array of 8 pins on it. Op amp rates 1mV as input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. Operational amplifier can operate supply current at 750μA. Voltage gain should remain at 126.02dB. On the buffer amps, there are 2 channels that can be used. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits.
LMC662AIM/NOPB Features
8 Pins
supply voltage of 5V
126.02dB voltage gain
Output Type: Rail-to-Rail
LMC662AIM/NOPB Applications
There are a lot of Texas Instruments LMC662AIM/NOPB Instrumentational OP Amps applications.
- Proportional operation circuits
- RF cable systems
- Weak signal detection
- Displayers for aircraft and air transportation control systems
- Test equipment
- Fission chambers
- Broadcasting
- Signal transformation
- Integrator circuits
- Semiconductor detectors
