LMC7101AYM5-TR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Supplier Device Package | SOT-23-5 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Series | IttyBitty® |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Base Part Number | LMC7101 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 800μA |
| Nominal Supply Current | 1.71mA |
| Current - Supply | 800μA |
| Slew Rate | 0.3V/μs |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±1.35V~6V |
| Output Current per Channel | 300mA |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 500 kHz |
| Gain Bandwidth Product | 500kHz |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Voltage - Input Offset | 110μV |
| Current - Output / Channel | 300mA |
| Number of Amplifiers | 1 |
| Height | 1.1mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMC7101AYM5-TR Overview
Packaging for the buffer amplifier is in the form of a SC-74A, SOT-753 case. An op amp ic of the General Purpose type. A Tape & Reel (TR) case is used for delivering the op amp. The buffer op amp includes 5 pins. In terms of the input offset voltage, instrumentation amplifier rates at 6mV. This electrical part should be mounted using type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureUsing a supply current of 800μA , this buffer op amp will be able to operate. On this buffer amplifier, there are 1 circuits. There are 1 channels on the operational amplifiers. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. It should not lower than -40°C to operate buffer amplifier. You should not use op amp above 85°C . The op amp is rated for an operating supply voltage of 1. For optimal performance, this electrical part should be connected to a supply with a current of 800μA. Regarding the voltage of the supply, this electrical part can work from a voltage as low as 12V, and this is an excellent feature. To keep the buffer amps' supply voltage higher than 2.7V. The IttyBitty? represents the op amp's series number. The buffer amplifier consists of 1 amplifiers.
LMC7101AYM5-TR Features
Output Type: Rail-to-Rail
LMC7101AYM5-TR Applications
There are a lot of Microchip Technology LMC7101AYM5-TR Instrumentational OP Amps applications.
- Communication device
- Inverse/same-phase proportional circuit
- Logarithmic operation circuits
- PDA
- Car stereo
- Measurements of Wheatstone bridge
- High gain DC amplifier
- Signal amplification
- Weighing systems
- pH (acidity)
