LMH6514SQE/NOPB
| Parameters | |
|---|---|
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.12kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | LMH6514 |
| Pin Count | 16 |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Power Supplies | 5V |
| Operating Supply Current | 107mA |
| Nominal Supply Current | 124mA |
| Output Current | 20mA |
| Slew Rate | 1600 V/us |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Variable Gain |
| Common Mode Rejection Ratio | 81 dB |
| Voltage - Supply, Single/Dual (±) | 4V~5.25V |
| Input Offset Voltage (Vos) | 30mV |
| Bandwidth | 600MHz |
| Voltage Gain | 30.3dB |
| Power Supply Rejection Ratio (PSRR) | 63dB |
| Frequency Compensation | YES |
| Micropower | NO |
| -3db Bandwidth | 600MHz |
| Programmable Power | NO |
| Input Voltage Noise Density | 1.8nV/sqrt Hz |
| Height | 800μm |
| Length | 4mm |
| Width | 4mm |
| Thickness | 750μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
LMH6514SQE/NOPB Overview
There is a 16-WFQFN Exposed Pad case in which the instrumentation amplifier is packaged. There are two types of operational amplifiers in this circuit. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 16. It consists of a total of 16 pins in total. I would like to remind you that this buffer op amp should be powered by an 5V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. In total, the buffer amplifier consists of 16 pins. Regarding input offset voltage, op amp rates 30mV. This electronic part is best mounted with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. A supply current of 107mA can be used to operate this linear amplifier. Maintain 30.3dB as the voltage gain. On the output type, there are Differential different types of op amps. The op amp is rated for an operating supply voltage of 1. The operating supply voltage of the buffer op amp is rated at 5V. It is used TR to pack the op amps. During testing, the buffer amplifier resistance should remain within a range of 1.12kOhm.
LMH6514SQE/NOPB Features
16 Pins
supply voltage of 5V
30.3dB voltage gain
Output Type: Differential
Resistance of 1.12kOhm
LMH6514SQE/NOPB Applications
There are a lot of Texas Instruments LMH6514SQE/NOPB Instrumentational OP Amps applications.
- High input resistance broadband
- Video data acquisition
- Broadcasting
- Industrial applications including automation
- Band-pass filter
- Multiplication circuits
- Division circuits
- Car stereo
- Tablets
- Inverse/same-phase proportional circuit
