LMH6515SQ/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.12kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | LMH6515 |
| Pin Count | 16 |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Power Supplies | 5V |
| Operating Supply Current | 107mA |
| Nominal Supply Current | 124mA |
| Output Current | 20mA |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Variable Gain |
| Common Mode Rejection Ratio | 85 dB |
| Voltage - Supply, Single/Dual (±) | 4V~5.25V |
| Input Offset Voltage (Vos) | 30mV |
| Bandwidth | 600MHz |
| Voltage Gain | 32dB |
| Power Supply Rejection Ratio (PSRR) | 83dB |
| Frequency Compensation | YES |
| Gain | 31 dB |
| Micropower | NO |
| -3db Bandwidth | 600MHz |
| Programmable Power | NO |
| Input Voltage Noise Density | 1.8nV/sqrt Hz |
| Height | 800μm |
| Length | 4mm |
| Width | 4mm |
| Thickness | 750μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMH6515SQ/NOPB Overview
Packaging for the buffer amplifier is in the form of a 16-WFQFN Exposed Pad case. This is a Variable Gain type op amp. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be at least 16 terminations this year. The pins on this board total to 16 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. An 16-pin op amp ic is included in the package. Regarding input offset voltage, buffer amplifier rates 30mV voltage. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. An 107mA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. One of the advantages of this op amp is that it outputs Differential signals, which is one of its many advantages. The linear amplifier consists of 1 different elements in total. The operating supply voltage of instrumentation amplifier is rated 5V voltage. A TR-shaped amplifier is used to pack the buffer amps. During testing, the instrumentation amplifier resistance should remain within a range of 1.12kOhm.
LMH6515SQ/NOPB Features
16 Pins
supply voltage of 5V
32dB voltage gain
Output Type: Differential
Resistance of 1.12kOhm
LMH6515SQ/NOPB Applications
There are a lot of Texas Instruments LMH6515SQ/NOPB Instrumentational OP Amps applications.
- Radiation thermometry transducers
- Exponential operation circuits
- Proportional counter tubes
- Mobile phone
- Power transmission
- Active probe
- Fast A/D and D/A converters
- High/low-pass filter circuit
- Ultrasound transducers
- Navigation
