LMH6618MK/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 Thin, TSOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Base Part Number | LMH6618 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Operating Supply Current | 1.35mA |
| Nominal Supply Current | 1.25mA |
| Output Current | 35mA |
| Slew Rate | 57V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 81 dB |
| Current - Input Bias | 1.5μA |
| Voltage - Supply, Single/Dual (±) | 2.7V~11V ±1.35V~5.5V |
| Output Current per Channel | 35mA |
| Input Offset Voltage (Vos) | 100μV |
| Gain Bandwidth Product | 65MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 71000 kHz |
| Voltage Gain | 100dB |
| Power Supply Rejection Ratio (PSRR) | 64dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 140MHz |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -5.5V |
| Wideband | YES |
| Input Offset Current-Max (IIO) | 0.27μA |
| Height | 1.1mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 870μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMH6618MK/NOPB Overview
Packaging for the buffer amplifier is in the form of a SOT-23-6 Thin, TSOT-23-6 case. There are two types of operational amplifiers in this circuit. A Tape & Reel (TR) case is used for delivering the op amp. The number of terminations is approaching the 6 mark. There are a total of 6 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 5V volts. Instrumentation amplifier is a part of Operational Amplifier. In total, the buffer amplifier consists of 6 pins. Regarding input offset voltage, buffer amplifier rates 100μV voltage. This electronic part is best mounted with type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. A supply current of 1.35mA can be used to operate this linear amplifier. 100dB should remain the voltage gain. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. As a whole, there are 1 elements that make up this buffer amplifier. It is used TR to pack the op amps.
LMH6618MK/NOPB Features
6 Pins
supply voltage of 5V
100dB voltage gain
Output Type: Rail-to-Rail
LMH6618MK/NOPB Applications
There are a lot of Texas Instruments LMH6618MK/NOPB Instrumentational OP Amps applications.
- MP3
- Signal amplification
- Vehicle electronics
- Professional videography
- Logarithmic operation circuits
- Integrator circuits
- Biopotential
- Displayers for aircraft and air transportation control systems
- Voltage regulation circuit
- Power transmission
