LMH6629SDE/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | LMH6629 |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Operating Supply Current | 15.5mA |
| Nominal Supply Current | 15.5mA |
| Slew Rate | 1600V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 82 dB |
| Current - Input Bias | 15μA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 250mA |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 900MHz |
| Gain Bandwidth Product | 190MHz |
| Unity Gain BW-Nom | 4000000 kHz |
| Voltage Gain | 78dB |
| Average Bias Current-Max (IIB) | 35μA |
| Power Supply Rejection Ratio (PSRR) | 81dB |
| Low-Offset | YES |
| Frequency Compensation | NO |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 190MHz |
| Max Frequency | 1MHz |
| Bias Current-Max (IIB) @25C | 23μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5.5V |
| Height | 800μm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 800μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMH6629SDE/NOPB Overview
It is packaged in an 8-WFDFN Exposed Pad-case that protects the operational amplifiers from damage. The instrumentation amplifier in this picture is of the Voltage Feedback-type. A Tape & Reel (TR) case is used for delivering the op amp. The number of terminations is approaching the 8 mark. The pins on this board total to 8 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3.3V. It should be noted that this op amp is a type of Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. Op amp rates 150μV as input offset voltage. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. As long as the supply current of the chip does not exceed 15.5mA, this op amp ic can operate. Keeping the voltage gain at 78dB is the best course of action. There are a total of 1 channels available on the op amps. As a result of this, the buffer amplifier is packed in TR.
LMH6629SDE/NOPB Features
8 Pins
supply voltage of 3.3V
78dB voltage gain
LMH6629SDE/NOPB Applications
There are a lot of Texas Instruments LMH6629SDE/NOPB Instrumentational OP Amps applications.
- MP3
- Video data acquisition
- Wireless base stations
- Precision measurement
- Radar
- Multiplication circuits
- Exponential operation circuits
- Biopotential
- Power control
- Signal amplification
