Parameters |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Base Part Number |
LMH6646 |
Pin Count |
8 |
Output Type |
Push-Pull, Rail-to-Rail |
Number of Channels |
2 |
Nominal Supply Current |
650μA |
Output Current |
20mA |
Current - Supply |
725μA |
Slew Rate |
22V/μs |
Amplifier Type |
Voltage Feedback |
Common Mode Rejection Ratio |
56 dB |
Current - Input Bias |
650nA |
Voltage - Supply, Single/Dual (±) |
2.5V~12V ±1.25V~6V |
Output Current per Channel |
20mA |
Input Offset Voltage (Vos) |
1mV |
Bandwidth |
55MHz |
Gain Bandwidth Product |
55MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Unity Gain BW-Nom |
40000 kHz |
Voltage Gain |
85dB |
Power Supply Rejection Ratio (PSRR) |
75dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
6.3V |
Low-Bias |
NO |
Micropower |
NO |
-3db Bandwidth |
55MHz |
Programmable Power |
NO |
Dual Supply Voltage |
5V |
Neg Supply Voltage-Max (Vsup) |
-6.3V |
Input Offset Current-Max (IIO) |
0.5μA |
Max Junction Temperature (Tj) |
150°C |
Height |
1.07mm |
Length |
3mm |
Width |
3mm |
Thickness |
970μm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C |
Packaging |
Tape & Reel (TR) |
Series |
VIP10™ |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
LMH6646MM/NOPB Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case which makes it easy for the consumer to handle. There are two types of operational amplifiers in this circuit. A Tape & Reel (TR) case is used to deliver the buffer op amp. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. It has 8 pins that make up the linear amplifier. Regarding input offset voltage, op amp rates 1mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperature85dB should remain the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels. One of the many benefits of this op amp ic is that it emits Push-Pull, Rail-to-Rail signals. For the packing of the instrumentation amplifier, TR is adopted. It is recommended that you use an 725μA power supply with this electrical part in order for it to operate correctly. Buffer op amp series numbers are indicated by the VIP10?.
LMH6646MM/NOPB Features
8 Pins
supply voltage of 5V
85dB voltage gain
Output Type: Push-Pull, Rail-to-Rail
LMH6646MM/NOPB Applications
There are a lot of Texas Instruments LMH6646MM/NOPB Instrumentational OP Amps applications.
- Thermocouples
- Broadcasting
- Proportional counter tubes
- Non-polarized electrodes
- Blood pressure sensors
- Commercial audio systems
- Weak signal detection
- PDA
- Video data acquisition
- Inverse/same-phase proportional circuit