LMH6658MA/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | LMH6658 |
| Pin Count | 8 |
| Number of Elements | 2 |
| Operating Supply Current | 6.5mA |
| Nominal Supply Current | 6.2mA |
| Output Current | 80mA |
| Max Supply Current | 17mA |
| Slew Rate | 700V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 72 dB |
| Current - Input Bias | 5μA |
| Voltage - Supply, Single/Dual (±) | 3V~12V ±1.5V~6V |
| Output Current per Channel | 110mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 270MHz |
| Gain Bandwidth Product | 140MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 140000 kHz |
| Voltage Gain | 95dB |
| Average Bias Current-Max (IIB) | 30μA |
| Power Supply Rejection Ratio (PSRR) | 72dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 100MHz |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Input Offset Current-Max (IIO) | 0.3μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMH6658MA/NOPB Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. The instrumentation amplifier in this picture is of the Voltage Feedback-type. A Tube case is used for delivering the op amp. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. It has 8 pins that make up the linear amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 5mV. For this electronic part, it is recommended that you mount it with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureIt is possible to operate this buffer amplifier from a supply current of 6.5mA . There should be no change in the voltage gain at 95dB. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2.
LMH6658MA/NOPB Features
8 Pins
supply voltage of 5V
95dB voltage gain
LMH6658MA/NOPB Applications
There are a lot of Texas Instruments LMH6658MA/NOPB Instrumentational OP Amps applications.
- Power control
- Signal transformation
- Band-pass filter
- Measurements of Wheatstone bridge
- Laptop
- Cinema or auditorium audio system
- Professional videography
- Active probe
- Band-stop filter
- Instrumentation
