LMH6683MTX/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | VIP10™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Base Part Number | LMH6683 |
| Pin Count | 14 |
| Number of Elements | 3 |
| Operating Supply Current | 6.5mA |
| Nominal Supply Current | 6.5mA |
| Output Current | 80mA |
| Slew Rate | 940V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 72 dB |
| Current - Input Bias | 5μA |
| Voltage - Supply, Single/Dual (±) | 3V~12V ±1.5V~6V |
| Output Current per Channel | 85mA |
| Input Offset Voltage (Vos) | 5mV |
| Gain Bandwidth Product | 380MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 100000 kHz |
| Voltage Gain | 95dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 190MHz |
| Bias Current-Max (IIB) @25C | 20μA |
| Programmable Power | NO |
| Wideband | YES |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMH6683MTX/NOPB Overview
A 14-TSSOP (0.173, 4.40mm Width) case is used to package the op amp. The instrumentation amplifier in this picture is of the Voltage Feedback-type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. The number of terminations approaches 14. There are a total of 14 pins on this op amp. Please take in mind that this instrumentation amplifier should be run at 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. There are 14 pins on this chip. Regarding input offset voltage, buffer amplifier rates 5mV voltage. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. An 6.5mA volt supply current is needed for this linear amplifier to operate. Op amp is a member of the 95dB's 95dB family. The op amp is rated for an operating supply voltage of 3. For the packing of the instrumentation amplifier, TR is adopted. In this case, VIP10? represents the instrumentation amplifiers' series number.
LMH6683MTX/NOPB Features
14 Pins
supply voltage of 5V
95dB voltage gain
LMH6683MTX/NOPB Applications
There are a lot of Texas Instruments LMH6683MTX/NOPB Instrumentational OP Amps applications.
- Logarithmic operation circuits
- Signal operation
- Television broadcasting equipment
- High input resistance broadband
- Micro signal measurement
- Video amplifiers
- Proportional operation circuits
- Wireless base stations
- Video computer boards
- Laptop
