banner_page

LMP2012MM/NOPB

2 Channels 17mA per Channel 3pA 100 dB Instrumentational OP Amps 0.000004μA 2.7V~5.25V LMP2012 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-LMP2012MM/NOPB
  • Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
  • Datasheet: -
  • Stock: 755
  • Description: 2 Channels 17mA per Channel 3pA 100 dB Instrumentational OP Amps 0.000004μA 2.7V~5.25V LMP2012 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 2 days ago)
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Number of Pins 8
Operating Temperature -40°C~125°C
Packaging Tape & Reel (TR)
Series LMP®
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Terminal Finish Matte Tin (Sn)
Subcategory Operational Amplifier
Packing Method TR
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 5V
Terminal Pitch 0.65mm
Base Part Number LMP2012
Pin Count 8
Output Type Rail-to-Rail
Number of Channels 2
Operating Supply Current 930μA
Nominal Supply Current 930μA
Output Current 18mA
Slew Rate 4V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 100 dB
Current - Input Bias 3pA
Voltage - Supply, Single/Dual (±) 2.7V~5.25V
Output Current per Channel 17mA
Input Offset Voltage (Vos) 36μV
Bandwidth 3MHz
Unity Gain BW-Nom 3000 kHz
Voltage Gain 105dB
Average Bias Current-Max (IIB) 0.000004μA
Power Supply Rejection Ratio (PSRR) 95dB
Low-Offset YES
Frequency Compensation YES
Voltage - Input Offset 0.12μV
Low-Bias YES
Micropower NO
Programmable Power NO
Height 1.07mm
Length 3mm
Width 3mm
Thickness 970μm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

LMP2012MM/NOPB Overview


It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. Op amps are General Purpose types of amplifier on the chip. A Tape & Reel (TR) case is used for delivering the op amp. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are located on the operational amplifiers. Op amp rates 36μV as input offset voltage. This electronic part is recommended for mounting type Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. You can run this op amp ic on 930μA . You should keep the voltage gain at 105dB for the time being. There are a total of 2 channels available on the op amps. On the output type, there are Rail-to-Rail different types of op amps. A TR-shaped amplifier is used to pack the buffer amps. The LMP? stands for the buffer op amp's serial number.

LMP2012MM/NOPB Features


8 Pins
supply voltage of 5V
105dB voltage gain
Output Type: Rail-to-Rail

LMP2012MM/NOPB Applications


There are a lot of Texas Instruments LMP2012MM/NOPB Instrumentational OP Amps applications.

  • Test and measurement instruments
  • Blood pressure sensors
  • Proportional counter tubes
  • Non-polarized electrodes
  • Car stereo
  • Communication
  • Polarized electrodes
  • Division circuits
  • Active probe
  • Precision measurement

Write a review

Note: HTML is not translated!
    Bad           Good