LMP2012WGLLQMLV
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Number of Pins | 10 |
| JESD-609 Code | e0 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 10 |
| Qualification Status | Not Qualified |
| Temperature Grade | MILITARY |
| Number of Channels | 2 |
| Max Supply Voltage | 5V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 930μA |
| Power Dissipation | 714mW |
| Current - Output | 18mA |
| Slew Rate | 4 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 3pA |
| Input Offset Voltage (Vos) | 36μV |
| Gain Bandwidth Product | 3MHz |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 132dB |
| Average Bias Current-Max (IIB) | 0.000003μA |
| Power Supply Rejection Ratio (PSRR) | 95dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Screening Level | 38535V;38534K;883S |
| Wideband | NO |
| Total Dose | 50k Rad(Si) V |
| Height | 2.34mm |
| Length | 6.858mm |
| Width | 6.121mm |
| Thickness | 1.778mm |
| Radiation Hardening | Yes |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
LMP2012WGLLQMLV Overview
An op amp of this type is a OPERATIONAL AMPLIFIER-type. The number of terminations is approaching the 10 mark. Buffer amplifier has a total of 10 pins. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. In total, the buffer amplifier consists of 10 pins. In terms of input offset voltage, operational amplifier rates 36μV. The voltage gain should stay at 132dB. There are 2 channels on the operational amplifiers. For this linear amplifier to work, the temperature should not be below -55°C. No temperature greater than 125°C should be used. In terms of the supply voltage, this electrical part is capable of operating at low voltage levels of under 5V. A high supply voltage of more than 2.7V is recommended for the instrumentation amplifier's supply voltage.
LMP2012WGLLQMLV Features
10 Pins
supply voltage of 5V
132dB voltage gain
LMP2012WGLLQMLV Applications
There are a lot of Texas Instruments LMP2012WGLLQMLV Instrumentational OP Amps applications.
- Fission chambers
- Home audio systems
- Micro signal measurement
- Weighing systems
- Broadcasting
- Television broadcasting equipment
- Logarithmic operation circuits
- Power control
- Measurements of Wheatstone bridge
- Differentiator circuits
