Parameters |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
81 dB |
Current - Input Bias |
0.02pA |
Voltage - Supply, Single/Dual (±) |
1.6V~5.5V |
Output Current per Channel |
30mA |
Input Offset Voltage (Vos) |
150μV |
Bandwidth |
130 kHz |
Unity Gain BW-Nom |
130 kHz |
Voltage Gain |
120dB |
Power Supply Rejection Ratio (PSRR) |
83dB |
Low-Offset |
YES |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
6V |
Voltage - Input Offset |
10μV |
Low-Bias |
YES |
Micropower |
YES |
Programmable Power |
NO |
Height |
1.45mm |
Length |
2.9mm |
Width |
1.6mm |
Thickness |
1.2mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
SC-74A, SOT-753 |
Number of Pins |
5 |
Operating Temperature |
-40°C~125°C |
Packaging |
Tape & Reel (TR) |
Series |
LMP®, PowerWise® |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
1.8V |
Base Part Number |
LMP2231 |
Pin Count |
5 |
Output Type |
Rail-to-Rail |
Number of Channels |
1 |
Operating Supply Current |
10μA |
Nominal Supply Current |
10μA |
Output Current |
30mA |
Slew Rate |
0.058V/μs |
Architecture |
VOLTAGE-FEEDBACK |
LMP2231AMFE/NOPB Overview
A SC-74A, SOT-753 case is used to package the op amp. This is a General Purpose type op amp. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. The number of terminations is approaching the 5 mark. A total of 5 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 1.8V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 5 pins are included on the operational amplifiers. There is an input offset voltage of 150μV for this buffer op amp. For this electronic part, it is recommended that you mount it with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing a supply current of 10μA , this buffer op amp will be able to operate. It is recommended to keep the voltage gain at 120dB at all times. The op amp ic has 1 channels on it. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The linear amplifier is packaged by using a TR axis. This buffer amplifier is assigned within the LMP?, PowerWise? series by its manufacturer.
LMP2231AMFE/NOPB Features
5 Pins
supply voltage of 1.8V
120dB voltage gain
Output Type: Rail-to-Rail
LMP2231AMFE/NOPB Applications
There are a lot of Texas Instruments LMP2231AMFE/NOPB Instrumentational OP Amps applications.
- Video conversion and routing
- Vehicle electronics
- Ultrasound transducers
- High/low-pass filter circuit
- Logarithmic operation circuits
- Mobile phone
- Integrator circuits
- Weak signal detection
- Blood pressure sensors
- Proportional operation circuits