LMP2234AMT/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | LMP®, PowerWise® |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 1.8V |
| Base Part Number | LMP2234 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 2/5V |
| Operating Supply Current | 36μA |
| Nominal Supply Current | 31μA |
| Output Current | 30mA |
| Slew Rate | 0.058V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 81 dB |
| Current - Input Bias | 0.02pA |
| Voltage - Supply, Single/Dual (±) | 1.6V~5.5V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 130 kHz |
| Unity Gain BW-Nom | 130 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Power Supply Rejection Ratio (PSRR) | 83dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 10μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Programmable Power | NO |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMP2234AMT/NOPB Overview
Packaged in a 14-TSSOP (0.173, 4.40mm Width) case, the buffer op amp is ready to use. An op amp of this type is a General Purpose-type. There is a Tube case that is delivered with the instrumentation amplifiers. There have been a total of 14 terminations over the past year. Buffer amplifier has a total of 14 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 1.8V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 14 pins are located on the operational amplifiers. Op amp rates 150μV as input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. The buffer amplifier is capable of operating from a supply current of 36μA . Maintain 120dB as the voltage gain. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 4. The LMP?, PowerWise? stands for the buffer op amp's serial number.
LMP2234AMT/NOPB Features
14 Pins
supply voltage of 1.8V
120dB voltage gain
Output Type: Rail-to-Rail
LMP2234AMT/NOPB Applications
There are a lot of Texas Instruments LMP2234AMT/NOPB Instrumentational OP Amps applications.
- Semiconductor detectors
- Wireless base stations
- Oscilloscopes
- Thermocouples
- Radar
- MP3
- Communication
- Large motor controllers
- Signal amplification
- Integrator circuits
