LMP7711MKE/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 Thin, TSOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | LMP®, PowerWise® |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.95mm |
| Base Part Number | LMP7711 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 1.15mA |
| Nominal Supply Current | 1.75mA |
| Slew Rate | 11.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 0.1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 66mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 17MHz |
| Unity Gain BW-Nom | 17000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 85dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 450μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Input Offset Current-Max (IIO) | 5e-7μA |
| Height | 1.1mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 870μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMP7711MKE/NOPB Overview
In order to protect the op amps, a SOT-23-6 Thin, TSOT-23-6 case is used. Buffer amps of this type are called General Purpose-types. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. The number of terminations is approaching the 6 mark. Linear amplifier has a total of 6 pins. Please take in mind that this instrumentation amplifier should be run at 2.5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 6 pins are located on the operational amplifiers. Regarding input offset voltage, buffer amplifier rates 500μV voltage. Surface Mount is the recommended mounting type of operational amplifiers. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . A supply current of 1.15mA can be used to operate this linear amplifier. 110dB should remain the voltage gain. There are 1 channels on the operational amplifiers. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. The operating supply voltage of the buffer op amp is rated at 5V. To pack the operational amplifier ics, TR is adopted as the packing method. This buffer amplifier is assigned within the LMP?, PowerWise? series by its manufacturer.
LMP7711MKE/NOPB Features
6 Pins
supply voltage of 2.5V
110dB voltage gain
Output Type: Rail-to-Rail
LMP7711MKE/NOPB Applications
There are a lot of Texas Instruments LMP7711MKE/NOPB Instrumentational OP Amps applications.
- Thermocouples
- Multiplication circuits
- Mobile phone
- PDA
- Video conversion and routing
- Laptop
- Video computer boards
- Radar
- Weak signal detection
- MP3
