LMP7716MM
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | LMP®, PowerWise® |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | LMP7716 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 1.3mA |
| Nominal Supply Current | 1.3mA |
| Output Current | 66mA |
| Slew Rate | 11.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 0.1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 66mA |
| Input Offset Voltage (Vos) | 10μV |
| Bandwidth | 17MHz |
| Unity Gain BW-Nom | 14000 kHz |
| Voltage Gain | 95dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 85dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Height | 860μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
LMP7716MM Overview
In the package, you will find a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case to contain the op amp ic. An op amp of this type is a General Purpose-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be 8 terminations in the next few months. The total number of pins on linear amplifier is 8. It is important to remember that this op amp should be operated at a voltage of 2.5V volts. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. It has 8 pins that make up the linear amplifier. With regard to input offset voltage, instrumentation amplifier is rated at 10μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . As long as the supply current of the chip does not exceed 1.3mA, this op amp ic can operate. You should keep the voltage gain at 95dB for the time being. Instrumentation amplifier has 2 channels on it. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. TAPE AND REEL is adopted to pack the instrumentation amplifier. In this case, LMP?, PowerWise? represents the instrumentation amplifiers' series number.
LMP7716MM Features
8 Pins
supply voltage of 2.5V
95dB voltage gain
Output Type: Rail-to-Rail
LMP7716MM Applications
There are a lot of Texas Instruments LMP7716MM Instrumentational OP Amps applications.
- Communication device
- Navigation
- Displayers for aircraft and air transportation control systems
- Signal amplification
- Test equipment
- Automatic control
- Addition operation circuits
- Television broadcasting equipment
- Commercial audio systems
- Cinema or auditorium audio system
