LMP7717MF/NOPB
| Parameters | |
|---|---|
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 10μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | LMP®, PowerWise® |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Base Part Number | LMP7717 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 1.15mA |
| Nominal Supply Current | 1.15mA |
| Output Current | 60mA |
| Slew Rate | 35V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 0.1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 60mA |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 88MHz |
| Unity Gain BW-Nom | 88000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 85dB |
LMP7717MF/NOPB Overview
There is a SC-74A, SOT-753 case package that contains the instrumentation amplifiers. General Purpose-type instrumentation amplifiers are used in this application. A Tape & Reel (TR) case is used for delivering the op amp. It is estimated that there will be 5 terminations in the next few months. The total number of pins on linear amplifier is 5. It would be helpful if you could remember that this op amp ic should be powered by an 2.5V battery. Instrumentation amplifier is a part of Operational Amplifier. The op amp ic has an array of 5 pins on it. In terms of the input offset voltage, instrumentation amplifier rates at 150μV. This electrical part should be mounted using type Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. This op amp can operate from a supply current at 1.15mA. 110dB should be the voltage gain. There are 1 channels on the operational amplifiers. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. TR is adopted to pack the instrumentation amplifier. The LMP?, PowerWise? indicates the series number of the op amp.
LMP7717MF/NOPB Features
5 Pins
supply voltage of 2.5V
110dB voltage gain
Output Type: Rail-to-Rail
LMP7717MF/NOPB Applications
There are a lot of Texas Instruments LMP7717MF/NOPB Instrumentational OP Amps applications.
- Test equipment
- Laptop
- Weighing systems
- Gaming industry
- Medical imaging
- Semiconductor detectors
- Switching amplifier
- Communication
- Power control
- Division circuits
