LMP8601MA/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | LMP® |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 590kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | LMP8601 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 1.1mA |
| Nominal Supply Current | 1.5mA |
| Output Current | 46mA |
| Max Supply Current | 1.3mA |
| Slew Rate | 0.83V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Current Sense |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 0.04pA |
| Voltage - Supply, Single/Dual (±) | 3V~5.5V |
| Output Current per Channel | 48mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 60 kHz |
| Unity Gain BW-Nom | 60 kHz |
| Voltage Gain | 26.06dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 150μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Voltage Gain-Nom | 20 |
| Common Mode Voltage-Max | 60V |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMP8601MA/NOPB Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. The instrumentation amplifier in this picture is of the Current Sense-type. A Tube case is used for delivering the op amp. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 3.3V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. The buffer op amp includes 8 pins. There is an input offset voltage of 1mV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . This op amp can operate from a supply current at 1.1mA. You should keep the voltage gain at 26.06dB for the time being. As far as the device is concerned, buffer amplifier has 1 channels. The operating supply voltage of the buffer op amp is rated at 5V. The LMP? indicates the series number of the op amp. It is important that the linear amplifier resistance stays within the range of 590kOhm.
LMP8601MA/NOPB Features
8 Pins
supply voltage of 3.3V
26.06dB voltage gain
Resistance of 590kOhm
LMP8601MA/NOPB Applications
There are a lot of Texas Instruments LMP8601MA/NOPB Instrumentational OP Amps applications.
- Non-polarized electrodes
- Power transmission
- Band-pass filter
- Wireless base stations
- PDA
- Biopotential
- Television broadcasting equipment
- ECG equipment
- Portable media players
- Television
