LMP8645HVMKE/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 Thin, TSOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Digi-Reel® |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Base Part Number | LMP8645 |
| Pin Count | 6 |
| Operating Supply Voltage | 9V |
| Number of Elements | 2 |
| Number of Channels | 1 |
| Operating Supply Current | 2.2mA |
| Nominal Supply Current | 610μA |
| Max Supply Current | 2.7mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Current Sense |
| Common Mode Rejection Ratio | 95 dB |
| Current - Input Bias | 13μA |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V |
| Output Current per Channel | 5mA |
| Input Offset Voltage (Vos) | 1.7mV |
| Bandwidth | 990 kHz |
| Gain Bandwidth Product | 260 kHz |
| Unity Gain BW-Nom | 990 kHz |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | YES |
| -3db Bandwidth | 860kHz |
| Programmable Power | NO |
| Voltage Gain-Min | 1 |
| Height | 1.1mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 870μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMP8645HVMKE/NOPB Overview
A SOT-23-6 Thin, TSOT-23-6 case is used to package the op amp. An op amp ic of the Current Sense type. A Digi-Reel? case is used for delivering the op amp. A total of 6 terminations have been reported in the past few weeks. The pins on this board total to 6 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 6 pins are included on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 1.7mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing a supply current of 2.2mA , this buffer op amp will be able to operate. There are 1 channels on the operational amplifiers. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2. The operating supply voltage of the buffer op amp is rated at 9V. TR is adopted to pack the instrumentation amplifier. The minimum voltage gain this buffer op amp is able to conduct is 1.
LMP8645HVMKE/NOPB Features
6 Pins
supply voltage of 5V
LMP8645HVMKE/NOPB Applications
There are a lot of Texas Instruments LMP8645HVMKE/NOPB Instrumentational OP Amps applications.
- Hand-held batteries
- pH (acidity)
- Blood pressure sensors
- Fast A/D and D/A converters
- Radar
- Power control
- Switching amplifier
- Video amplifiers
- Video conversion and routing
- Precision measurement
