LMS4684ITLX/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 12-WFBGA |
| Number of Pins | 12 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Resistance | 500mOhm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | LMS4684 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 5V |
| Power Supplies | 3V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 5nA |
| Nominal Supply Current | 5nA |
| Turn On Delay Time | 60 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.000005mA |
| Turn-Off Delay Time | 40 ns |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 60ns, 40ns |
| Charge Injection | 200pC |
| Channel-to-Channel Matching (ΔRon) | 1.11m Ω |
| Crosstalk | -72dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 675μm |
| Length | 2mm |
| Width | 1.8mm |
| Thickness | 675μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMS4684ITLX/NOPB Overview
Presented in 12-WFBGA, this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 2:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~85°C TA are extended for operation. In total, there are 12 terminations. This electronic part offers high-quality output due to its 2 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. Circuits based on SPDT switching are used to construct these analog switch ics. If you are looking for variants of the digital switch, trying search with LMS4684. There is 500mOhm internal resistance in this digital multiplexer. Please refer to the datasheets for 12 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 1.8V. It would be sufficient to run this analogue multiplexer with 5nA current. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. This electrical part is compatible with 5V operating voltages. The 2 inputs need to be operated in order to work. The analog switch ics includes 4 outputs.
LMS4684ITLX/NOPB Features
2 Channels
Switch Circuit: SPDT
5nA Supply Current
LMS4684ITLX/NOPB Applications
There are a lot of Texas Instruments LMS4684ITLX/NOPB Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Modems
- RGB switches
- Remote Powered Equipment
- Data Acquisition Systems
- Cell phones
- Audio and video signal routing
- Precision data acquisition
- Residential Gateways, Home Gateway/Router
- Routers
