LMS4684LD/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-WFDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 800mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Base Part Number | LMS4684 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Power Supplies | 3V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 5nA |
| Nominal Supply Current | 5μA |
| Max Supply Current | 5nA |
| Turn On Delay Time | 60 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 60ns, 40ns |
| Charge Injection | 200pC |
| Channel-to-Channel Matching (ΔRon) | 1.11m Ω |
| Crosstalk | -72dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 65ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Drain to Source Resistance | 800mOhm |
| Height | 800μm |
| Length | 4mm |
| Width | 3mm |
| Thickness | 800μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMS4684LD/NOPB Overview
The electronic component is convenient to ship overseas because it is packed in a 10-WFDFN Exposed Pad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. Totally, there are 10 terminations. As a result of its 2 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 2.7V voltage supply. A total of 10 pins are injected into the electrical part body. The analog switch ics are built using SPDT switching circuits. Try searching for LMS4684 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 800mOhm. Datasheets for 10 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. Multiplexers should not be powered above 5.5V in normal situations. An effective Single supply digital multiplexer. There should be 1.8V voltage fed to the electrical part below 1.8V. It would be sufficient to run this analogue multiplexer with 5nA current. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 5nA. The 2 inputs need to be operated in order to work. There is 800mOhm resistance between Drain and Source for this electronic part. There are 4 outputs on the analogue multiplexer.
LMS4684LD/NOPB Features
2 Channels
Switch Circuit: SPDT
5nA Supply Current
Drain-to-Source resistance: 800mOhm
LMS4684LD/NOPB Applications
There are a lot of Texas Instruments LMS4684LD/NOPB Analog Switches & Multiplexers ICs applications.
- FTTH
- ISDN NT1/TA
- MP3 players
- Intelligent PBX
- Digital cross connects (DSX-1)
- Digital access cross connects
- Digital Cross-Connects
- Imaging
- Fault Tolerant Systems
- SONET
