LMV324DR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 1.27mm |
| Base Part Number | LMV324 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Power Supplies | 2.7/5V |
| Number of Channels | 4 |
| Operating Supply Current | 410μA |
| Nominal Supply Current | 830μA |
| Output Current | 160mA |
| Slew Rate | 1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 1nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Halogen Free | Halogen Free |
| Output Current per Channel | 160mA |
| Input Offset Voltage (Vos) | 9mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 100dB |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 1.7mV |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1MHz |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMV324DR2G Overview
Packaging for the buffer amplifier is in the form of a 14-SOIC (0.154, 3.90mm Width) case. General Purpose-type instrumentation amplifiers are used in this application. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. The number of terminations approaches 14. A total of 14 pins are attached to buffer op amp. Please take in mind that this instrumentation amplifier should be run at 2.7V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. There are 14 pins on this chip. Op amp rates 9mV as input offset voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . It is possible to operate this buffer amplifier from a supply current of 410μA . Op amp is a member of the 100dB's 100dB family. On the buffer amps, there are 4 channels that can be used. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 3V. The linear amplifier is packaged by using a TAPE AND REEL axis.
LMV324DR2G Features
14 Pins
supply voltage of 2.7V
100dB voltage gain
Output Type: Rail-to-Rail
LMV324DR2G Applications
There are a lot of ON Semiconductor LMV324DR2G Instrumentational OP Amps applications.
- Signal amplification
- Gaming industry
- Video data acquisition
- Home audio systems
- RF cable systems
- Logarithmic operation circuits
- Precision measurement
- Mobile phone
- Laptop
- Displayers for aircraft and air transportation control systems
