LMV324MTX/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | LMV324 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Operating Supply Current | 410μA |
| Nominal Supply Current | 410μA |
| Output Current | 60mA |
| Slew Rate | 1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 15nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Output Current per Channel | 160mA |
| Input Offset Voltage (Vos) | 7mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 1.7mV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.25μA |
| Programmable Power | NO |
| Input Offset Current-Max (IIO) | 0.05μA |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMV324MTX/NOPB Overview
In order to protect the op amps, a 14-TSSOP (0.173, 4.40mm Width) case is used. A General Purpose-type buffer amplifier is shown here. Linear amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be 14 terminations in the next few months. It consists of a total of 14 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. 14 pins are located on the operational amplifiers. Op amp rates 7mV as input offset voltage. Surface Mount is the recommended mounting type for this linear amplifier. With regard to operating temperature, this op amp functions well at -40°C~85°C. As long as the supply current of the chip does not exceed 410μA, this op amp ic can operate. 100dB should remain the voltage gain. As far as the device is concerned, buffer amplifier has 4 channels. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. An buffer amplifier is packed in a TR-shape according to the design.
LMV324MTX/NOPB Features
14 Pins
supply voltage of 5V
100dB voltage gain
Output Type: Rail-to-Rail
LMV324MTX/NOPB Applications
There are a lot of Texas Instruments LMV324MTX/NOPB Instrumentational OP Amps applications.
- Active probe
- Measurements of Wheatstone bridge
- Gaming industry
- Weak signal detection
- Television broadcasting equipment
- Thermocouples
- Laptop
- ECG equipment
- Biopotential
- Signal amplification
