LMV358DR2G
| Parameters | |
|---|---|
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 hours ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Base Part Number | LMV358 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 2 |
| Operating Supply Current | 210μA |
| Nominal Supply Current | 440μA |
| Output Current | 160mA |
| Slew Rate | 1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 1nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Halogen Free | Halogen Free |
| Output Current per Channel | 160mA |
| Input Offset Voltage (Vos) | 9mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 100dB |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 1.7mV |
| Low-Bias | NO |
| Micropower | YES |
| Max Frequency | 50kHz |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1MHz |
| Height | 1.5mm |
LMV358DR2G Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. Buffer amps of this type are called General Purpose-types. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. There is a growing number of terminations approaching the number of 8. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 2.7V volts. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The op amp ic has an array of 8 pins on it. Regarding input offset voltage, op amp rates 9mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . As long as the supply current of the chip does not exceed 210μA, this op amp ic can operate. There should be no change in the voltage gain at 100dB. Instrumentation amplifier has 2 channels on it. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of instrumentation amplifier is rated 3V voltage. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
LMV358DR2G Features
8 Pins
supply voltage of 2.7V
100dB voltage gain
Output Type: Rail-to-Rail
LMV358DR2G Applications
There are a lot of ON Semiconductor LMV358DR2G Instrumentational OP Amps applications.
- Multimedia playback equipment
- Radiation thermometry transducers
- Band-stop filter
- Power generator
- Automatic control
- Portable media players
- Computer workstations
- Hand-held batteries
- Weak signal detection
- Signal transformation
