LMV712LD/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-WFDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Base Part Number | LMV712 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Operating Supply Current | 1.17mA |
| Nominal Supply Current | 1.22mA |
| Output Current | 25mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 5.5pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 130dB |
| Average Bias Current-Max (IIB) | 0.00013μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 400μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000115μA |
| Programmable Power | NO |
| Wideband | NO |
| Height | 800μm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 800μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMV712LD/NOPB Overview
There is a 10-WFDFN Exposed Pad case package that contains the instrumentation amplifiers. An op amp ic of the General Purpose type. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be 10 terminations in the next few months. A total of 10 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 2.7V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 10 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 3mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. An 1.17mA volt supply current is needed for this linear amplifier to operate. It is a member of the 130dB's 130dB family. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2. This linear amplifier pack is based on the TR axis.
LMV712LD/NOPB Features
10 Pins
supply voltage of 2.7V
130dB voltage gain
Output Type: Rail-to-Rail
LMV712LD/NOPB Applications
There are a lot of Texas Instruments LMV712LD/NOPB Instrumentational OP Amps applications.
- Instrumentation
- Differentiator circuits
- Test and measurement instruments
- Blood pressure sensors
- Radar
- Video data acquisition
- Large motor controllers
- Division circuits
- Fission chambers
- Information processing
