LMV712TL/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Copper, Silver, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-WFBGA |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BICMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | LMV712 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 1.17mA |
| Nominal Supply Current | 1.22mA |
| Output Current | 25mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 5.5pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 7mV |
| Bandwidth | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 130dB |
| Average Bias Current-Max (IIB) | 0.00013μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 400μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000115μA |
| Programmable Power | NO |
| Height | 675μm |
| Length | 0m |
| Width | 0m |
| Thickness | 360μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMV712TL/NOPB Overview
Op amp is packaged in 10-WFBGA case. General Purpose-type instrumentation amplifiers are used in this application. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. The number of terminations approaches 10. A total of 10 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 10 pins. With regard to input offset voltage, instrumentation amplifier is rated at 7mV. This electrical part should be mounted using type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. A supply current of 1.17mA can be used to operate this linear amplifier. Keeping the voltage gain at 130dB is the best course of action. Op amp ic has 2 channels. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. A TR-shaped amplifier is used to pack the buffer amps.
LMV712TL/NOPB Features
10 Pins
supply voltage of 5V
130dB voltage gain
Output Type: Rail-to-Rail
LMV712TL/NOPB Applications
There are a lot of Texas Instruments LMV712TL/NOPB Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Communication device
- ECG equipment
- Broadcasting
- Displayers for aircraft and air transportation control systems
- single/dual op amp sum and difference circuits
- Large motor controllers
- High-frequency data acquisition systems
- Thermocouples
- Professional videography
