LMV712TLX/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Copper, Silver, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-WFBGA, DSBGA |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BICMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | LMV712 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Operating Supply Current | 1.17mA |
| Nominal Supply Current | 1.22mA |
| Output Current | 25mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 5.5pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 7mV |
| Gain Bandwidth Product | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 130dB |
| Average Bias Current-Max (IIB) | 0.00013μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 400μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000115μA |
| Programmable Power | NO |
| Wideband | NO |
| Height | 675μm |
| Length | 0m |
| Width | 0m |
| Thickness | 360μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMV712TLX/NOPB Overview
There is a 10-WFBGA, DSBGA case package that contains the instrumentation amplifiers. Op amps are General Purpose types of amplifier on the chip. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. It is estimated that there will be at least 10 terminations this year. The pins on this board total to 10 in total. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. There are 10 pins on this chip. Op amp ic rates 7mV for input offset voltage. This electronic part is best mounted with type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . Using a supply current of 1.17mA , this buffer op amp will be able to operate. Maintain 130dB as the voltage gain. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2. A TR-shaped amplifier is used to pack the buffer amps.
LMV712TLX/NOPB Features
10 Pins
supply voltage of 5V
130dB voltage gain
Output Type: Rail-to-Rail
LMV712TLX/NOPB Applications
There are a lot of Texas Instruments LMV712TLX/NOPB Instrumentational OP Amps applications.
- Video amplifiers
- Inverse/same-phase proportional circuit
- Logarithmic operation circuits
- Wireless base stations
- Digital cameras
- Radar
- Radiation thermometry transducers
- Polarized electrodes
- Commercial audio systems
- Band-pass filter
