LMV716MM/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | LMV716 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 2 |
| Operating Supply Current | 1.6mA |
| Nominal Supply Current | 1.6mA |
| Output Current | 20mA |
| Slew Rate | 5.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 0.6pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5V |
| Output Current per Channel | 41mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 122dB |
| Average Bias Current-Max (IIB) | 0.000115μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 1.6mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000115μA |
| Programmable Power | NO |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMV716MM/NOPB Overview
It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. The instrumentation amplifier in this picture is of the General Purpose-type. The op amp is delivered to you in a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. It consists of a total of 8 pins in total. As a reminder, this buffer op amp should be powered by 3.3V battery and that the battery should be inserted in the amplifier. To be specific, this instrumentation amplifier is a type of Operational Amplifier. A total of 8 pins are present on the instrumentation amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 5mV. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. As long as the supply current of the chip does not exceed 1.6mA, this op amp ic can operate. Keeping the voltage gain at 122dB is the best course of action. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. As a whole, there are 2 elements that make up this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 3V. A TR-shaped amplifier is used to pack the buffer amps.
LMV716MM/NOPB Features
8 Pins
supply voltage of 3.3V
122dB voltage gain
Output Type: Rail-to-Rail
LMV716MM/NOPB Applications
There are a lot of Texas Instruments LMV716MM/NOPB Instrumentational OP Amps applications.
- Industrial control system
- High/low-pass filter circuit
- Signal transformation
- High gain DC amplifier
- Broadcasting
- Addition operation circuits
- Radar
- Radiation thermometry transducers
- Navigation
- Blood pressure sensors
