LMV771MG/NOPB
| Parameters | |
|---|---|
| Slew Rate | 1.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.23pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Input Offset Voltage (Vos) | 850μV |
| Bandwidth | 3.5MHz |
| Unity Gain BW-Nom | 3500 kHz |
| Voltage Gain | 100dB |
| Power Supply Rejection Ratio (PSRR) | 82dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 250μV |
| Current - Output / Channel | 75mA |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | LMV771 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Nominal Supply Current | 550μA |
| Output Current | 18mA |
| Current - Supply | 600μA |
LMV771MG/NOPB Overview
There is a 5-TSSOP, SC-70-5, SOT-353 case package that contains the instrumentation amplifiers. A General Purpose-type buffer amplifier is shown here. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be 5 terminations in the next few months. The total number of pins on linear amplifier is 5. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. It should be noted that this op amp is a type of Operational Amplifier device. In total, the buffer amplifier consists of 5 pins. The input offset voltage is 850μV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. 100dB should remain the voltage gain. Op amp ic has 1 channels. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. TR is adopted to pack the instrumentation amplifier. As a result, it is recommended that a power supply of 600μA be used with this electronic part.
LMV771MG/NOPB Features
5 Pins
supply voltage of 5V
100dB voltage gain
Output Type: Rail-to-Rail
LMV771MG/NOPB Applications
There are a lot of Texas Instruments LMV771MG/NOPB Instrumentational OP Amps applications.
- Large motor controllers
- Broadcasting
- Radar
- Displayers for aircraft and air transportation control systems
- Signal transformation
- Measurements of Wheatstone bridge
- Proportional operation circuits
- Communication device
- Vehicle electronics
- E-book readers
