LMV931MG/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Base Part Number | LMV931 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Nominal Supply Current | 103μA |
| Output Current | 8mA |
| Current - Supply | 116μA |
| Slew Rate | 0.42V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 14nA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Input Offset Voltage (Vos) | 4mV |
| Bandwidth | 1.5MHz |
| Unity Gain BW-Nom | 1500 kHz |
| Voltage Gain | 113dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Current - Output / Channel | 100mA |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMV931MG/NOPB Overview
It is packaged in an 5-TSSOP, SC-70-5, SOT-353-case that protects the operational amplifiers from damage. This is a General Purpose type op amp. Linear amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 5. A total of 5 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 2.7V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The op amp ic has an array of 5 pins on it. Regarding input offset voltage, op amp rates 4mV. Surface Mount is the recommended mounting type for this linear amplifier. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. There should be no change in the voltage gain at 113dB. Op amp ic has 1 channels. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. The operating supply voltage of instrumentation amplifier is rated 3V voltage. To pack the operational amplifier ics, TR is adopted as the packing method. As a recommendation, this electronic component should be used with a power supply that can deliver 116μA.
LMV931MG/NOPB Features
5 Pins
supply voltage of 2.7V
113dB voltage gain
Output Type: Rail-to-Rail
LMV931MG/NOPB Applications
There are a lot of Texas Instruments LMV931MG/NOPB Instrumentational OP Amps applications.
- Signal filtering
- Power transmission
- Integrator circuits
- Blood pressure sensors
- Scintillation detectors
- Broadcasting
- Logarithmic operation circuits
- Thermocouples
- Inverse/same-phase proportional circuit
- Comparator
