LMV932DMR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifiers |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.65mm |
| Base Part Number | LMV932 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 95μA |
| Nominal Supply Current | 190μA |
| Slew Rate | 0.48V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 1nA |
| Max Input Voltage | 5V |
| Voltage - Supply, Single/Dual (±) | 1.8V~5V |
| Halogen Free | Halogen Free |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 1.5MHz |
| Unity Gain BW-Nom | 1400 kHz |
| Voltage Gain | 90dB |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LMV932DMR2G Overview
Packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case, the buffer op amp is ready to use. Op amps are General Purpose types of amplifier on the chip. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. There is a growing number of terminations approaching the number of 8. Linear amplifier has a total of 8 pins. The linear amplifier should be run at 2.7V at all times, so please keep that in mind when using it. There are two types of Operational Amplifiers op amps in this case, and this device falls into one of them. 8 pins are available on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 1mV. The mounting type that is recommended for this electrical part is Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . An 95μA volt supply current is needed for this linear amplifier to operate. Keeping the voltage gain at 90dB is the best course of action. The op amp ic has 2 channels on it. On the output type, there are Rail-to-Rail different types of op amps. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
LMV932DMR2G Features
8 Pins
supply voltage of 2.7V
90dB voltage gain
Output Type: Rail-to-Rail
LMV932DMR2G Applications
There are a lot of ON Semiconductor LMV932DMR2G Instrumentational OP Amps applications.
- Professional videography
- Non-polarized electrodes
- High gain DC amplifier
- Video conversion and routing
- Measurements of Wheatstone bridge
- Exponential operation circuits
- Portable media players
- High-frequency data acquisition systems
- Switching amplifier
- Weak signal detection
