LNK306DN
| Parameters | |
|---|---|
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Voltage | 700V |
| Max Supply Voltage | 265V |
| Min Supply Voltage | 85V |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Nominal Supply Current | 250μA |
| Output Current | 360mA |
| Topology | Buck, Buck-Boost, Flyback |
| Min Input Voltage | 85V |
| Max Input Voltage | 265V |
| Control Technique | PULSE WIDTH MODULATION |
| Internal Switch(s) | Yes |
| Fault Protection | Current Limiting, Open Loop, Over Temperature, Short Circuit |
| Max Duty Cycle | 72 % |
| Drain to Source Resistance | 7Ohm |
| Duty Cycle | 69% |
| Output Isolation | Non-Isolated |
| Min Input Voltage (AC) | 85V |
| Max Input Voltage (AC) | 265V |
| Height | 1.65mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width), 7 Leads |
| Number of Pins | 8 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Published | 2007 |
| Series | LinkSwitch®-TN |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Power Rating | 80mW |
| Max Power Dissipation | 12mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Frequency | 66kHz |
LNK306DN Overview
The ac to dc converter is embedded in 8-SOIC (0.154, 3.90mm Width), 7 Leads package.The AC/DC power converter is available in Tube .Surface Mount mounts this AC/DC converter.To deliver its performance, the ac dc converter should be operated at a temperature of -40°C~150°C TJ .The AC DC converter uses a type SWITCHING REGULATOR analog integrated circuit.There are a total of 8 terminations.On this ac/dc converter, there are 8 pins.The pins of the ac-dc converter total to 8 .Surface Mount is the recommended mounting method for the ac dc converters.It belongs to the family of LinkSwitch?-TN manufacturers.The number of outputs to run is 1 .In this AC to DC transformer, the output current is set to 360mA .There is 700V output voltage from this AC/DC converter.This power AC DC is capable of reaching high efficiency when operating at a frequency of 66kHz .You can read the standard of REACH SVHC : No SVHC .The AC to DC converter can be powered from the input voltage under 265V .It is possible to use the AC to DC inverter with an input voltage less than 85V V.AC to DC power converters should be able to accept input voltages (AC) below 265V .AC to DC converter can work with the minimum supply voltage of 85V .
LNK306DN Features
Packaged with 8-SOIC (0.154, 3.90mm Width), 7 Leads
With 8 pins
Output Current at 360mA
LNK306DN Applications
There are a lot of Power Integrations LNK306DN AC DC Converters applications.
- Standby and Auxiliary Power Supplies Set Top Boxes (STB)
- RCC SMPS
- Z-Wave
- Charger
- Power tools fast chargers with trickle and on/off
- Standby Power Supplies
- SMPS house keeping power supplies
- White goods
- Portable Apparatus
- Chargers for cell/cordless phones
