LNK364GN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SMD (7 Leads), Gull Wing |
| Number of Pins | 8 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Published | 2007 |
| Series | LinkSwitch®-XT |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 4 (72 Hours) |
| Number of Terminations | 7 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Terminal Finish | PURE MATTE TIN |
| Power Rating | 9W |
| Max Power Dissipation | 9W |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 250 |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Frequency | 132kHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G7 |
| Number of Outputs | 1 |
| Output Voltage | 5.8V |
| Output Type | Adjustable |
| Max Output Current | 750mA |
| Min Supply Voltage | 50V |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Nominal Supply Current | 250μA |
| Output Current | 750mA |
| Topology | Flyback |
| Min Input Voltage | 85V |
| Max Input Voltage | 265V |
| Control Technique | PULSE WIDTH MODULATION |
| Switcher Configuration | SINGLE |
| Internal Switch(s) | Yes |
| Fault Protection | Current Limiting, Open Loop, Over Temperature, Short Circuit |
| Max Duty Cycle | 60 % |
| Max Supply Voltage (AC) | 265V |
| Duty Cycle | 60% |
| Output Isolation | Isolated |
| Voltage - Breakdown | 700V |
| Max Input Voltage (AC) | 265V |
| Min Supply Voltage (AC) | 85V |
| Height | 3.68mm |
| Length | 9.83mm |
| Width | 6.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
LNK364GN Overview
An embedded ac to dc converter is included in 8-SMD (7 Leads), Gull Wing package.The AC/DC power converter is available in Tube .The AC/DC converter is mounted in the way of Surface Mount .For the ac dc converter to perform at its best, it should be operated at a temperature of -40°C~150°C TJ °C.Analog IC type SWITCHING REGULATOR is utilized in this AC DC converter.It has a total of 7 terminations.There are 8 pins on the ac/dc converter.There are a total of 8 pins on the ac-dc converter.There are no problem mounting the ac dc converters by Surface Mount .The product is acdc converter of the LinkSwitch?-XT manufacturer family.AC to DC converter is necessary to run 1 outputs.It has been set to 750mA for the output current.The output voltage of the AC/DC converter is 5.8V .AC to DC converter is able to reach high efficiency when its frequency is 132kHz .You can read the standard of REACH SVHC : No SVHC .The AC to DC converter can be powered from the input voltage under 265V .If the input voltage is less than 85V V, the AC to DC inverter can be used.A minimum voltage supply across the converter is 85V .This converter can operate at a maximum supply voltage of 265V .AC to DC power converters should be able to accept input voltages (AC) below 265V .As long as the supply voltage is 50V , it will operate.There is a Adjustable output configured.
LNK364GN Features
Packaged with 8-SMD (7 Leads), Gull Wing
With 8 pins
Output Current at 750mA
Output Type : Adjustable
LNK364GN Applications
There are a lot of Power Integrations LNK364GN AC DC Converters applications.
- AC/DC LED Driver applications
- SMPS house keeping power supplies
- Standby Power Supply
- Linear Adapter Replacements
- Automotive Telematics
- ATX/BTX Auxiliary Power
- Adapter/Charger for Cell
- Battery chargers for smart phones
- Auxiliary Power Supplies
- DVD players
