LNK605PG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm), 7 Leads |
| Number of Pins | 8 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Published | 2008 |
| Series | LinkSwitch®-II |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Terminal Finish | MATTE TIN |
| Power Rating | 5.1W |
| Max Power Dissipation | 5.1W |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Frequency | 66kHz |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Voltage | 6V |
| Analog IC - Other Type | ANALOG CIRCUIT |
| Operating Supply Current | 480μA |
| Power Dissipation | 4.5W |
| Output Current | 337mA |
| Output Power | 5.1W |
| Topology | Flyback |
| Min Input Voltage | 85V |
| Frequency - Switching | Up to 85kHz |
| Max Input Voltage | 265V |
| Internal Switch(s) | Yes |
| Fault Protection | Current Limiting, Open Loop, Over Temperature, Short Circuit |
| Max Duty Cycle | 55 % |
| Max Supply Voltage (AC) | 265V |
| Output Isolation | Isolated |
| Voltage - Breakdown | 700V |
| Min Input Voltage (AC) | 85V |
| Max Input Voltage (AC) | 265V |
| Min Supply Voltage (AC) | 85V |
| Height | 3.68mm |
| Length | 9.83mm |
| Width | 6.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
LNK605PG Overview
An embedded ac to dc converter is included in 8-DIP (0.300, 7.62mm), 7 Leads package.The AC/DC power converter type is Tube .Through Hole is mounted in the way of this AC/DC converter.For the ac dc converter to perform properly, it should be operated at a temperature of -40°C~150°C TJ °C.In this AC DC converter, an analog integrated circuit (IC) of type ANALOG CIRCUIT is employed.The switching frequency reaches Up to 85kHz .Total terminations are 8 .In this ac/dc converter, there are 8 pins.There are a total of 8 pins on the ac-dc converter.It are possible to mount thare ac dc converters by Through Hole .This AC to DC converter belongs to the LinkSwitch?-II manufacturer family.There are 1 outputs to run.It has been set to 337mA for the output current.There is 6V output voltage from this AC/DC converter.This power AC DC is capable of reaching high efficiencies when operating at a frequency of 66kHz .SVHC for REACH can be found in the standard No SVHC .The AC to DC converter can be powered under 265V voltage.The output power of a coverter generates 5.1W .An input voltage of less than 85V volts is acceptable for use with this AC to DC inverter.Across the converter, the minimum supply voltage is 85V .There is a maximum voltage supply across the converter of 265V volts.It is recommended to keep the voltage (AC) that can be applied to the AC to DC power converter below 265V .
LNK605PG Features
Packaged with 8-DIP (0.300, 7.62mm), 7 Leads
Switching Frequency at Up to 85kHz
With 8 pins
Output Current at 337mA
LNK605PG Applications
There are a lot of Power Integrations LNK605PG AC DC Converters applications.
- Battery Chargers
- Low power ac?dc Adapters for Chargers
- AC/DC Adaptors/Chargers for E-books
- Appliances
- MPS parts
- Consumer electronics
- Standby Power Supplies
- AC-DC Output Power Conversion Applications
- Power Adaptors
- Small off-line low voltage power supplies
