banner_page

LNK606PG

8 Terminations8 Pin AC to DC power converterLinkSwitch?-II Series 1 OutputsUp to 85kHz Min 85V VMax 265V V


  • Manufacturer: Power Integrations
  • Nocochips NO: 633-LNK606PG
  • Package: 8-DIP (0.300, 7.62mm), 7 Leads
  • Datasheet: PDF
  • Stock: 200
  • Description: 8 Terminations8 Pin AC to DC power converterLinkSwitch?-II Series 1 OutputsUp to 85kHz Min 85V VMax 265V V(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Through Hole
Mounting Type Through Hole
Package / Case 8-DIP (0.300, 7.62mm), 7 Leads
Number of Pins 8
Operating Temperature -40°C~150°C TJ
Packaging Tube
Published 2002
Series LinkSwitch®-II
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
Terminal Finish MATTE TIN
Power Rating 6.1W
Max Power Dissipation 6.1W
Terminal Position DUAL
Number of Functions 1
Terminal Pitch 2.54mm
Frequency 66kHz
Pin Count 8
Number of Outputs 1
Output Voltage 6V
Analog IC - Other Type ANALOG CIRCUIT
Operating Supply Current 520μA
Output Current 438mA
Output Power 6.1W
Topology Flyback
Min Input Voltage 85V
Frequency - Switching Up to 85kHz
Max Input Voltage 265V
Internal Switch(s) Yes
Fault Protection Current Limiting, Open Loop, Over Temperature, Short Circuit
Max Duty Cycle 55 %
Max Supply Voltage (AC) 265V
Output Isolation Isolated
Voltage - Breakdown 700V
Min Input Voltage (AC) 85V
Max Input Voltage (AC) 265V
Min Supply Voltage (AC) 85V
Height 3.68mm
Length 9.83mm
Width 6.6mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status RoHS Compliant

LNK606PG Overview


In the package 8-DIP (0.300, 7.62mm), 7 Leads , the ac to dc converter is embedded.In Tube AC/DC power converter, it is available.A AC/DC converter of this type is mounted in the way of Through Hole .It is necessary to operate the ac dc converter at a temperature of -40°C~150°C TJ °C in order for it to perform properly.This AC DC converter employs ANALOG CIRCUIT analog IC type.When the switching frequency reaches Up to 85kHz , the circuit is closed.Total terminations are 8 .Approximately 8 pins are present on the ac/dc converter.There are 8 pins in the ac-dc converter.Through Hole are the recommended mounting method for the ac dc converters.It belongs to a manufacturer family of LinkSwitch?-II .There are 1 outputs to run.In this AC to DC transformer, the output current is set to 438mA .The voltage output by this AC/DC converter is 6V .High efficiency can be achieved when AC to DC converters frequency is set to 66kHz .SVHC for REACH can be found in the standard No SVHC .Input voltages under 265V can be used to power the AC to DC converter.Coverters generate 6.1W in terms of output power.An input voltage of less than 85V V is required to operate the AC to DC inverter.A minimum voltage supply across the converter is 85V .265V is the maximum supply voltage across the converter.An input voltage (AC) should be applied to the AC to DC power converter that falls below 265V volts.

LNK606PG Features


Packaged with 8-DIP (0.300, 7.62mm), 7 Leads
Switching Frequency at Up to 85kHz
With 8 pins
Output Current at 438mA

LNK606PG Applications


There are a lot of Power Integrations LNK606PG AC DC Converters applications.

  • AC/DC LED Driver applications
  • Set -Top Box (STB) Power Supply
  • Replaces linear transformers
  • AC--DC Adapter
  • Power tools fast chargers with trickle and on/off
  • Z-Wave
  • Humidifier
  • Automotive Clusters
  • Standby Power for General Off-Line Applications
  • Battery Chargers

Write a review

Note: HTML is not translated!
    Bad           Good