LOG102AIDR
| Parameters | |
|---|---|
| Supply Voltage | 5V |
| Base Part Number | LOG102 |
| Pin Count | 14 |
| Operating Supply Voltage | 36V |
| Number of Elements | 4 |
| Power Supplies | +-5V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Analog IC - Other Type | LOG OR ANTILOG AMPLIFIER |
| Operating Supply Current | 1.25mA |
| Nominal Supply Current | 2mA |
| Max Output Voltage | 1.5V |
| Slew Rate | 0.5V/μs |
| Amplifier Type | Logarithmic and Log Ratio |
| Common Mode Rejection Ratio | 86 dB |
| Current - Input Bias | 5pA |
| Max Input Voltage | -2V |
| Voltage - Supply, Single/Dual (±) | ±4.5V~18V |
| Output Current per Channel | 18mA |
| Input Offset Voltage (Vos) | 750μV |
| Bandwidth | 45 kHz |
| Gain Bandwidth Product | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Voltage Gain | 88dB |
| Min Output Voltage | 1.2V |
| Power Supply Rejection Ratio (PSRR) | 106dB |
| Voltage - Input Offset | 300μV |
| Max Input Current | 1mA |
| Positive Input Voltage-Max | 3.5V |
| Negative Input Voltage-Max | -3.8V |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Analog Computational Functions |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
LOG102AIDR Overview
The linear amplifier is packaged in a 14-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. An op amp of this type is a Logarithmic and Log Ratio-type. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. A total of 14 terminations have been reported in the past few weeks. In this case, there are 14 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. This particular linear amplifier is a type of Analog Computational Functions device, to be precise. 14 pins are available on the instrumentation amplifier. There is an input offset voltage of 750μV for this buffer op amp. Surface Mount is the recommended mounting type for this linear amplifier. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. An 1.25mA volt supply current is needed for this linear amplifier to operate. It is recommended to keep the voltage gain at 88dB at all times. This op amp contains 1 circuits. Buffer op amp is equipped with 2 channels on the device. The buffer op amp is rated for an operating voltage of 4 when it comes to the power supply. The operating supply voltage of instrumentation amplifier is rated 36V voltage. The buffer op amp also uses a LOG OR ANTILOG AMPLIFIER analog IC.
LOG102AIDR Features
14 Pins
supply voltage of 5V
88dB voltage gain
LOG102AIDR Applications
There are a lot of Texas Instruments LOG102AIDR Instrumentational OP Amps applications.
- pH (acidity)
- Test equipment
- ECG equipment
- Exponential operation circuits
- Subtraction operation circuits
- Hand-held batteries
- Oscilloscopes
- Proportional operation circuits
- Image computer boards
- Non-polarized electrodes
