LP2902DR
| Parameters | |
|---|---|
| Nominal Supply Current | 150μA |
| Output Current | 10mA |
| Slew Rate | 0.05V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 2nA |
| Voltage - Supply, Single/Dual (±) | 3V~32V ±1.5V~16V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 4mV |
| Bandwidth | 100 kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 96.9dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 32V |
| Voltage - Input Offset | 2mV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.02μA |
| Programmable Power | NO |
| Power | NO |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | LP2902 |
| Pin Count | 14 |
| Operating Supply Voltage | 16V |
| Power Supplies | +-1.5/+-16/3/32V |
| Number of Channels | 4 |
| Operating Supply Current | 85μA |
LP2902DR Overview
Packaged in a 14-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. General Purpose-type instrumentation amplifiers are used in this application. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. It is estimated that there will be 14 terminations in the next few months. There are a total of 14 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 5V volts. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. In total, the buffer amplifier consists of 14 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 4mV. The mounting type that is recommended for this electrical part is Surface Mount. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Using an 85μA supply current, this operational amplifier ics can be operated. The voltage gain should stay at 96.9dB. The op amp ic has 4 channels on it. The operating supply voltage of the buffer op amp is rated at 16V. As a result of this, the buffer amplifier is packed in TR.
LP2902DR Features
14 Pins
supply voltage of 5V
96.9dB voltage gain
LP2902DR Applications
There are a lot of Texas Instruments LP2902DR Instrumentational OP Amps applications.
- Fission chambers
- Blood pressure sensors
- Radar
- Commercial audio systems
- Portable electronic products powered by batteries
- Displayers for aircraft and air transportation control systems
- Car stereo
- Proportional counter tubes
- Polarized electrodes
- Vehicle electronics
