LP2902MX/NOPB
| Parameters | |
|---|---|
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | LP2902 |
| Pin Count | 14 |
| Operating Supply Voltage | 13V |
| Number of Elements | 4 |
| Power Supplies | 5/30V |
| Operating Supply Current | 85μA |
| Nominal Supply Current | 85μA |
| Output Current | 20mA |
| Slew Rate | 0.05V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 2nA |
| Voltage - Supply, Single/Dual (±) | 3V~26V ±1.5V~13V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 4mV |
| Gain Bandwidth Product | 100kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 92.04dB |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 26V |
| Voltage - Input Offset | 2mV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.02μA |
| Programmable Power | NO |
| Wideband | NO |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 9 hours ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
LP2902MX/NOPB Overview
Packaging for the buffer amplifier is in the form of a 14-SOIC (0.154, 3.90mm Width) case. Op amps are General Purpose types of amplifier on the chip. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. There is a growing number of terminations approaching the number of 14. Buffer amplifier has a total of 14 pins on it. This linear amplifier should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. The op amp ic has an array of 14 pins on it. Regarding input offset voltage, buffer amplifier rates 4mV voltage. This electronic part is recommended for mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. It is possible to operate this buffer amplifier from a supply current of 85μA . Op amp is a member of the 92.04dB's 92.04dB family. The op amp is rated for an operating supply voltage of 4. The operating supply voltage of the buffer op amp is rated at 13V. An buffer amplifier is packed in a TR-shape according to the design.
LP2902MX/NOPB Features
14 Pins
supply voltage of 5V
92.04dB voltage gain
LP2902MX/NOPB Applications
There are a lot of Texas Instruments LP2902MX/NOPB Instrumentational OP Amps applications.
- High input resistance broadband
- MP3
- Weak signal detection
- Measurements of Wheatstone bridge
- RF cable systems
- Hand-held batteries
- Power transmission
- Proportional counter tubes
- High/low-pass filter circuit
- Gaming industry
