LP324DR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | LP324 |
| Pin Count | 14 |
| Operating Supply Voltage | 16V |
| Number of Elements | 4 |
| Power Supplies | +-1.5/+-16/3/32V |
| Operating Supply Current | 85μA |
| Nominal Supply Current | 150μA |
| Output Current | 10mA |
| Slew Rate | 0.05V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 2nA |
| Voltage - Supply, Single/Dual (±) | 3V~32V ±1.5V~16V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 4mV |
| Bandwidth | 100 kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.01μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 32V |
| Voltage - Input Offset | 2mV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.01μA |
| Programmable Power | NO |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LP324DR Overview
Packaging for the buffer amplifier is in the form of a 14-SOIC (0.154, 3.90mm Width) case. General Purpose-type instrumentation amplifiers are used in this application. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. It is estimated that there will be 14 terminations in the next few months. In this case, there are 14 pins on the board. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 14 pins are available on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 4mV. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, this op amp functions well at 0°C~70°C. An 85μA volt supply current is needed for this linear amplifier to operate. Op amp is a member of the 100dB's 100dB family. The linear amplifier consists of 4 different elements in total. The operating supply voltage of instrumentation amplifier is rated 16V voltage. To pack the operational amplifier ics, TR is adopted as the packing method.
LP324DR Features
14 Pins
supply voltage of 5V
100dB voltage gain
LP324DR Applications
There are a lot of Texas Instruments LP324DR Instrumentational OP Amps applications.
- Addition operation circuits
- Active probe
- Communication
- Fast A/D and D/A converters
- Blood pressure sensors
- PDA
- High input resistance broadband
- Mobile phone
- Measurements of Wheatstone bridge
- Ultrasound transducers
